Alfa Network 40-MS Manuel d'utilisateur

G2 802.11bg High-Power Outdoor AP/CPE USER MANUAL

z WAN Interface Setup This page is used to configure WAN access type Screen snapshot – WAN Interface Setup z Wireless Basic Settings This page i

z Wireless Security Setup This page is used to configure wireless security Screen snapshot – Wireless Security Setup 2.3.3 Operation Mode This pa

LAN interface, WAN interface, Wireless interface, NAT and Firewall modules are applied to this mode Bridge Each interface (LAN, WAN and Wireless) reg

Item Description Disable Wireless LAN Interface Click on to disable the wireless LAN data transmission. Band Click to select 2.4GHz(B) / 2.4GHz(G

will have on your G2. Screen snapshot – Wireless Advanced Settings Item Description Authentication Type Click to select the authentication type

pull-down menu. Data rate can be auto-select, 11M, 5.5M, 2M or 1Mbps. Preamble Type Click to select the Long Preamble or Short Preamble support on

Screen snapshot – Wireless Security Setup Item Description Encryption Select the encryption supported over wireless access. The encryption method

pull-down menu. The format can be Passphrase or Hex (64 characters). [WPA, Personal(Pre-Shared Key) only] Pre-Shared Key Fill in the key value. [WPA,

104-bit). Key Format Select the WEP shared secret key format from pull-down menu. The format can be chose between plant text (ASCII) and hexadecimal

Screen snapshot – Wireless Access Control Item Description Wireless Access Control Mode Click the Disabled, Allow Listed or Deny Listed of drop d

1 Installation 1.1 Hardware Installation diagram 1. Plug Power adapter into APoE02-WM 2. Connect RJ45 ( LAN Po

2.3.8 WDS Settings Wireless Distribution System uses wireless media to communicate with other APs, like the Ethernet does. To do this, you must set

Show Statistics It shows the TX, RX packets, rate statistics Delete Selected Click to delete the selected clients that will be removed from the wire

Screen snapshot – WDS AP Table Item Description MAC Address It shows the MAC Address within WDS. Tx Packets It shows the statistic count of sen

Screen snapshot – Wireless Site Survey Item Description SSID It shows the SSID of AP. BSSID It shows BSSID of AP. Channel It show the current

Screen snapshot – LAN Interface Setup Item Description IP Address Fill in the IP address of LAN interfaces of this WLAN Access Point. Subnet Mas

Domain Name Assign Domain Name and dispatch to DHCP clients. It is optional field. 802.1d Spanning Tree Select to enable or disable the IEEE 802.1d S

interface. There are IP address, subnet mask and default gateway settings need to be done. IP Address If you select the Static IP support on WAN inte

the new configuration setting. Reset Click the Reset button to abort change and recover the previous configuration setting. z DHCP Client Screen s

2. DNS 3 Fill in the IP address of Domain Name Server 3. Clone MAC Address Fill in the MAC address that is the MAC address to be cloned. Refer to 4.2

Item Description PPPoE Click to select PPPoE support on WAN interface. There are user name, password, connection type and idle time settings need

2 Software configuration There are web based management and configuration functions allowing you to have the jobs done easily. The G2 is delivered w

Attain DNS Automatically Click to select getting DNS address for PPPoEsupport. Please select Set DNS Manually if the PPPoE support is selected. Set DN

z PPTP Screen snapshot – WAN Interface Setup – PPTP Item Description PPTP Allow user to make a tunnel with remote site directly to secure the d

MTU Size Fill in the mtu size of MTU Size. The default value is 1400. Refer to 4.23 What is Maximum Transmission Unit (MTU) Size? Request MPPE Encryp

Screen snapshot – Firewall - Port Filtering Item Description Enable Port Filtering Click to enable the port filtering security function. Port Ran

Use of such filters can be helpful in securing or restricting your local network. Screen snapshot – Firewall - IP Filtering Item Description Ena

2.3.14 Firewall - MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through

2.3.15 Firewall - Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the

list. Reset Click the Reset button to abort change and recover the previous configuration setting. Delete Selected Click to delete the selected IP ad

settings. Reset Click the Reset button to abort change and recover the previous configuration setting. Delete Selected Click to delete the selected U

2.3.18 VPN Setting This page is used to show VPN connection table, configure IPSEC VPN, NAT Traversal, Generate RSA Key, Show RSA Public Key. Scre

For OS of Microsoft Windows 2000, XP: 1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear

radio button stay. Refresh Click to refresh the current VPN connection table. z VPN Setup - Edit Tunnel Screen snapshot – VPN Setup-Edit-1 Item

Local/Peer ID Local ID Type Local ID Remote ID Type Remote ID Define IKE exchange information type Click to select IP, DNS or E-mail as local exchang

Authentication Key Fill in authentication key. [Manual mode only] Apply Change Click the Apply Changes button to save current tunnel settings. Reset

Negotiation Mode Main mode. Encryption Algorithm Click to select 3DES or AES128 encryption. Authentication Algorithm Click to select MD5 or SHA1 auth

Screen snapshot – Management - Statistics Item Description Wireless LAN Sent Packets It shows the statistic count of sent packets on the wireless

Screen snapshot – Management – DDNS Item Description Enable DDNS Click the checkbox to enable DDNS service. Refer to 4.25 What is DDNS? Service

Screen snapshot – Management – Time Zone Settings Item Description Current Time It shows the current time. Time Zone Select Click the time zone

Screen snapshot – Management – Denial-of-Service Item Description Enable DoS Prevention Click the checkbox to enable DoS prevention. Whole System

2.3.23 Management - Log This page is used to configure the remote log server and shown the current log. Screen snapshot – Management – Log Item D

Screen snapshot – Management - Upgrade Firmware Item Description Select File Click the Browse button to select the new version of web firmware

box. 7. Select Specify an IP address and type in values as following example. 9 IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.16

to update the selected configuration to the G2. Reset Settings to Default Click the Reset button to reset the configuration parameter to factory defau

2.3.27 Logout This page is used to logout web management page. This item will be activated next time you login after you define user account and pass

Item Description System Uptime It shows the duration since G2 is powered on. Firmware version It shows the firmware version of G2. Wireless con

G2. Subnet Mask It shows the IP subnet mask of WAN interface of G2. Default Gateway It shows the default gateway setting for WAN interface outgoing

Screen snapshot – Operation Mode z Time Zone Setting This page is used to enable and configure NTP client Screen snapshot – Time Zone Settings z

Screen snapshot – LAN Interface Setup